GTM46101-1005-USB represents GlobTek’s 10 Watt wall plug-in series of AC/DC adapters (power supplies & chargers) with International Interchangeable blades and integral USB Jack. GlobTek’s changeable input blade system with individual field replaceable input plugs, including: North America / Japan NEMA 1-15P, Australian, UK BS 1363, European CEE 7/16 configuration, Korean KS C8305, Argentina IRAM 2073, China GB, India IS 1923 6A/SANS 164-3/BS546, IEC320/C18 Inlet, Brazilian NBR6147, S. African SANS 164-1 and British Standard BS 546-15A configurations and Global Regulatory & Safety Approvals and Certifications.
In 2014 the Electrotechnical Commission (IEC) released Edition 2.0 of the 62368-1 standard. This standard covers hazards and hazard prevention in the domain of information technology (ITE) and audio/visual (A/V) equipment, including consumer electronics, musical instruments, office appliances, and telecom hardware, and is intended to replace IEC 60950-1 and IEC 60065 sometime in 2019.
In addition to mandated government regulations, GlobTek is now starting to develop “greener” power supplies by increasing efficiencies and pushing the implementation of control technologies that in some cases eliminate no-load power consumption altogether. GTM46101-1005-USB family of Level VI compliant adapters are designed to keep OEMs one step ahead of the coming legislation by implementation of latest energy saving technologies into our external power supplies in order to address market demands and comply with current and future regulations.
Description / Features:
GlobTek’s GTM46101-1005-USB series of enclosed power supplies are housed in Impact resistant non-vented Polycarbonate Thermal Conduction-Cooled Cases and feature regulated outputs with very low ripple, built-in overcurrent, short circuit, overvoltage and thermal protection, as well as low leakage, low ripple, and high efficiency.
• Input Voltage: Specified 90-264 Vac, Nameplate rated 100-240 Vac
• Input Frequency: Specified 47-63 Hz, Nameplate rated 50-60 Hz
• Output Power (Rated): 10 Watts maximum
• Output Voltage: 5 to 6Vo with 0.1V increments
• Output Regulation: +/- 5% measured at the output connector
• Line Voltage Regulation: +/- 1% typical measured at the output connector
• Output Ripple (Vp-p): +/-1% or 150 mV whichever is greater at nominal output voltage. Measured at 20 MHz bandwidth with 0.1 uf ceramic capacitor in parallel with 10 uf electrolytic capacitor connected at the end of the output connector.
• Turn-On/Turn-Off Overshoot: 5% maximum, 500 us maximum recovery time for 25% step load.
• Turn-On Delay: 3000 mSEC maximum
• Hold-Up Time: 8mSec maximum at nominal input and full load.
• Inrush Current: 30A typical @ 115Vac input ; 60A typical @ 230Vac input
• Switching Frequency: 66.5 KHz typical
• Over-Voltage: Protected unit will recover upon removal of fault
• Short Circuit: Electronically Protected, unit will recover upon removal of fault
• Input Protection: Input line fusing
• ESD: 8 kV Contact/20kV Air Discharge
• Operating Temperature: 0°C to 40°C ambient temperature
• Humidity: 0% to 95% relative humidity
• Storage Temperature: -40°C to 80°C
• Housing: High impact plastic, 94V0 polycarbonate, non-vented
• Size: 41.0 x 71.0 x 31.5 mm +/-1.0 mm
Certifications / Approvals / Safety Compliance:
• MTBF: 200,000 Hours @ 25°C ambient temperature
• RoHS 2: Complies with EU 2011/65/EU China SJ/T 11364-2014
• Dielectric Withstand Voltage: 5656Vdc from primary to secondary
• Earth Leakage Current: N/A for Class II units, there is no PE Ground pin, so Earth Leakage current is not measured
• Touch Current: Maximum allowed values: 100uA NC(Normal condition) 500uA SFC(single fault condition)
• Means of Protection: 2 x MOPP
• GOST-R mark for Russia
• IP20 Ingress Protection: IP20 to IEC60529:2001 Protected against solids objects over 12mm and No Protection
• Efficiency: complies to section 301 of Energy Independence and Security Act (EISA) complies with Energy Star tier 2 (North America), ECP tier 2 (China), MEPS tier 2 (Australia), Code of Conduct (Europe)
• JAPAN PSE CQC Globtek Inc to J60950 AND J55022.
• RoHS 2: Complies with EU 2011/65/EU and CHINA SJ/T 11363-2006
• Semko S-Mark-Cert-EN60601-1 3rd Edition (http://www.intertek.com/marks/s/)
• S-Mark Certificate EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 +A2:2013
• Ukraine UKRSepro
• WEEE: Complies with EU 2012/19/EU
Our certification is accepted by the OSHA Nationally Recognized Testing Laboratory (NRTL) Program which is required for demonstrating compliance to UL standards for switching power supplies. The units are certified 2xMOPP (means of patient protection), which refers to two independent systems of insulation protecting the patient from dangerous voltages. A single insulating component can get this rating based on extensive testing. 2xMOPP certifications exceeds the requirements of 2xMOOP and these power supplies may be used for either application. In addition the series complies with 60601-1-11 Home health care standards.
Aside from 2xMOPP rating, the model is designed to withstand ESD surge ratings of 8kV Contact / 20kV Air.
Bespoke, customized enclosure colors, output connectors, housing designs, output cord types and lengths, customized packaging, including open frame or ruggedized to various degrees of Ingress Protection. Test reports and certifications as well, as variety of other customizations or options is available upon request.
These products can be supplied with customer designated output plugs, many of which are stocked at GlobTek New Jersey USA, Münster Germany, and Suzhou China locations.
Made in USA or Made in China options available. Local China to China delivery is available upon request.
Industry – Leading 5 year warranty on all products, excluding battery cells!
This family of Industry’s high density wall plug-in AC-DC charging converters is suitable for most applications requiring DC power which include industrial, marine, consumer or optional medical devices, portable medical treatment and monitoring equipment & instruments, hospital equipment and fixtures, Lighting and Support Equipment, low power appliances or consumer products, VOIP phones and telecom equipment and are a perfect power source for rapid Li-Ion and other emerging chemistries battery charging.
GlobTek is a power systems solutions provider with design and manufacturing facilities in the USA and China with sales offices in Germany, France, and the UK. Offering a line of power supplies, energy systems, PoEs, LED drivers, power cords, battery packs and many other power-related products and services for applications from gym equipment to medical systems, GlobTek can also develop and create custom power solutions for just about any requirement. As an ISO-13485 certified manufacturer of medical devices, GlobTek specializes in World-Wide safety compliant and ruggedized standard, modified and custom devices at an unbeatable cost vs. quality ratio!
GlobTek’s Headquarters including R&D, Engineering, Warehousing, Sales & Marketing, Testing and Assembly is located at 186 Veterans Drive, Northvale NJ 07647. For more information call 201-784-1000 or visit GlobTek online at www.globtek.com