Regulated Switchmode AC-DC Power Supply AC Adaptor
Category
ICT/ITE Power Supply/Class 2 Power Unit
Input Voltage Range (V)
100-240V~, 50-60 Hz
Max Input Current (A)
1.0A
Max Output Power Rating (W)
40
Output Voltage Range (V)
12-48
Efficiency
V
Ingress Protection
IP52
Size (mm)
43.5 x 74.0 x 35.3
Enclosure
Rating Table
Model Number (Final ordering #/Part No to be defined)
Voltage (V)
Current (A)
Power (W)
RFQ
GT-43007-4024-5.0*
19
2.1
39.9
GT-43007-4024*
24
1.67
40.08
GT-43007-3024-5.0*
19
1.57
29.83
GT-43007-3024-9.0*
15
2.66
39.9
GT-43007-3612*
12
3
36
GT-43007-4024-4.0*
20
2
40
GT-43007-4048*
48
0.833
39.98
GT-43007-4024-10.5*
13.5
2.96
39.96
GT-43007-4024-6.0*
19
2.2
41.8
GT-43007-4024-9.0*
15
2.66
39.9
GT-43007-3212*
12
2.67
32.04
GT-43007-3024*
24
1.25
30
GT-43007-3824-9.0*
15
2.5
37.5
GT-43007-3024-4.0*
20
1.5
30
GT-43007-4036*
36
1.1
39.6
GT-43007-3012*
12
2.5
30
GT-43007-4024-5.0*
19
2.1
39.9
GT-43007-4024*
24
1.67
40.08
GT-43007-3024-5.0*
19
1.57
29.83
GT-43007-3024-9.0*
15
2.66
39.9
GT-43007-3612*
12
3
36
GT-43007-4024-4.0*
20
2
40
GT-43007-4048*
48
0.833
39.98
GT-43007-4024-10.5*
13.5
2.96
39.96
GT-43007-4024-6.0*
19
2.2
41.8
GT-43007-4024-9.0*
15
2.66
39.9
GT-43007-3212*
12
2.67
32.04
GT-43007-3024*
24
1.25
30
GT-43007-3824-9.0*
15
2.5
37.5
GT-43007-3024-4.0*
20
1.5
30
GT-43007-4036*
36
1.1
39.6
GT-43007-3012*
12
2.5
30
* (Final ordering #/Part No to be defined)
Specifications
A) ELECTRICAL SPECIFICATIONS: 01.Input Voltage: Specified 90-264 Vac, Nameplate rated 100-240 Vac 02.Input Frequency: Specified 47-63 Hz, Nameplate rated 50-60 Hz 03. Output Regulation: +/- 5% measured at the output connector 04. Line Voltage Regulation: +/- 1% typical measured the output connector 05. Output Ripple (Vp-p): +/-1% or 150 mV whichever is greater at nominal output voltage. Measured at 20 MHz bandwidth with 0.1 uf ceramic capacitor in parallel with 10 uf electrolytic capacitor connected at the end of the output connector. 06 Turn-ON/OFF Overshoot: 5% maximum, 500uS max recovery time for 25% step load. 07. Turn-ON Delay: 3000 mS maximum. 08. Hold-Up Time: 10 mS Minimum at nominal input and full load. 09. Inrush Current: 30A maximum at cold start, 120Vac, 60A maximum cold start 230 Vac 10. Switching Frequency: 65 KHz typical
B) PROTECTION 01. Over-Voltage: Protected, unit will auto recover upon removal of fault 02. Short Circuit: Protected, unit will auto recover upon removal of fault 03. Input Protection: Input line fusing
C) SAFETY 01. Dielectric Withstand Voltage: 4242Vdc from primary to secondary 02. Touch Current: <0.25mA @ 240Vac input voltage 03. ROHS 2: Complies with EU 2011/65/EU and China SJ/T 11363-2006
D) OTHER: 01. MTBF: 200,000 Hours @ 25°C ambient temperature 02. Operating Temperature: 0°C to 40°C ambient temperature 03. Humidity: 0% to 90% relative humidity 04. Storage Temperature: -40°C to 80°C 05. Cooling: Convection
E) ENCLOSURE 01. Housing: High impact plastic, 94V0 polycarbonate, non-vented 02. Size: 43.5 x 74.0 x 35.3 +/- 1.0 mm 03. Markings: Label and/or Pad Printed and/or Molded in the case
INPUT CONNECTOR: Q-Socket (below are available blades configurations which are "not included" (unless stated above); can be purchased separately, package with power supply or as a separate "Q-KIT" if specified
01. United States / Canada / Japan NEMA 1-15P/ IEC PLUG Type A [WORKS IN PLUG B] configuration: NA 2 blades, Class II; US/CA/JP P/N: Q-NA(R) 02. Australian AS 3112 configuration: SAA 2 blade/ IEC TYPE I, Class II; AU P/N: Q-SAA(R) 03. UK BS 1363 configuration: UK 3 blade with dummy Ground/ IEC TYPE G, Class II; GB P/N: Q-UK(R) 04. European CEE 7/16 configuration: Europlug 2 pins/ IEC TYPE C [WORKS IN TYPE E&F], Class II; EU P/N: Q-EU(R) 05. Korean KS C8305 configuration: 2 pins/SIMILAR TO IEC TYPE C, Class II; KR P/N: Q-KR(R) 06. Argentina IRAM 2073 configuration: 2 blades/SIMILAR TO IEC TYPE I; AR P/N: Class II Q-AR(R) 07. China GB 2099 configuration: 2 blades/SIMILAR TO TYPE A, Class II; CN P/N:Q-CN(R) 08. India IS 1293 6A/BS546 configuration: 5A, 3 pins with Dummy Ground, Class II/IEC TYPE D; IN P/N: Q-IN(R) 09. IEC60320/C18 Inlet, Class II; P/N:Q-C18(R) 10. Brazilian NBR6147 configuration: 2 pins, Class II;SIMILAR TO IEC TYPE C BR P/N: Q-BR(R) 11. South Africa SABS164-1 and India IS 1293, IS694, 16A type plug, 3 round prongs, Class II + dummy ground, IEC TYPE M P/N: Q-SANS164-1-16A(R) 12. South Africa SABS164-4, 3 round prongs with a notched prong @ 0º, Class II + dummy ground, IEC TYPE M Red, P/N: Q-SANS164-4C-16A(R) 13. South Africa SABS164-4, 3 round prongs with a notched prong @ -53º, Class II + dummy ground, Blue, IEC TYPE M, P/N: Q-SANS164-4L-16A(R) 14. South Africa SABS164-4, 3 round prongs with a notched prong @ +53º, Class II + dummy ground, Black,IEC TYPE M P/N: Q-SANS164-4R-16A(R)
Contact GlobTek for your specific requirements or custom solutions.
Approvals
Below follows a link to the latest regulatory certifications and marks for this specific product. National standards as well as certification schemes are constantly changing and so is the set of certification marks and symbols applicable to this product. Various standards, marks and symbols, and certificates are subject to change at any time without notice.
Additional standards or unique country certifications are available upon request. Please contact Globtek to request a quotation.
Logo
Description
null
Indoor Use Only - Mark is on the label or Molded in the case
CHINA SJ/T 11364-2014, China RoHS Chart: http://www.globtek.com/pdf/F-GT-DJD-8.4.1-006%20China%20RoHS%20Declaration%205-20-22.pdf
UKCA Certification
WEEE: Complies with EU 2012/19/EU (http://ec.europa.eu/environment/waste/weee/index_en.htm) Mark is on the label or Molded in the case
FCC PART 15 CLASS B
Japan: Voluntary Control Council for Interference (VCCI)
JAPAN TUV Rheinland-PSE GlobTek Inc to J60950-1(H26) , J55022(H22),J3000(H25).Please follow the procedure listed in the following link for proper import to Japan: https://www.globtek.com/r2/Szj4Vb
CCC to GB4943.1-2011; GB/T9254-2008 GB17625.1-2012, Tropical <2000
RoHS
Specifications of directive 2011/65/EU Annex VI (ROHS-2) with amendment 2015/863-EU (ROHS-3) http://www.ce-mark.com/Rohs%20final.pdf
No Logo
CB Certificate IEC 60950-1:2005 (2nd Edition), Am 1: 2009, CB report IEC 60950-1:2005 (2nd Edition), Am 1: 2009 and EN 60950-1:2006 + Am 1:2010 + Am 11:2009 + Am 12:2011
JAPAN TUV R-PSE, Cert. No. JD 50473430, to J62368-1(H30) , J55032(H29),J3000(H25)[15V or less]. Please reference the following website for guidelines on PSE regulations: https://www.globtek.com/r2/Szj4Vb
Conforms to UL Std. 1310 CLASS 2 Power Units Cert. to CSA Std. C22.2 NO. 223 Up to 36 volts
UL60950-1, cULus to UL 60950-1, 2nd Edition, 2007-03-27 and CSA C22.2 No. 60950-1-07, 2nd Edition, 2007-03
Efficiency: complies to section 301 of Energy Independence and Security Act (EISA) complies with Energy Star tier 2 (North America), ECP tier 2 (China), MEPS tier 2 (Australia), Code of Conduct (Europe)
SELV
safety/separated extra-low voltage IEC 60950-1: 2005 (2nd Edition) and/or EN 60950-1:2006
Class 2 Power Unit
cETLus-Cert 4007497 UL1310 Recognized Component up to 42.4 volts
IP52
Ingress Protection: ?IP52 to IEC60529:2001 Protected against dust - limited ingress (no harmful deposit) and Protected against direct sprays up to 15 degrees from the vertical
CE Mark: tested to comply with EN 55032.2012+AC.2013, Class B, EN610003-2, EN610003-3 including EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6N EN61000-4-11; EMI: Complies with EN55011 CLASS B and FCC Part 15B - On label or Molded in case
LPS
Limited Power Source 60950
No Logo Applicable
CB report 60950-1 2nd Ed
Certification # TC RU AR46.B.75423 Custom Union of Russia, Belarus and Kazakhstan
Indoor Use Only - Mark is on the label or Molded in the case
CHINA SJ/T 11364-2014, China RoHS Chart: http://www.globtek.com/pdf/F-GT-DJD-8.4.1-006%20China%20RoHS%20Declaration%205-20-22.pdf
UKCA Certification
WEEE: Complies with EU 2012/19/EU (http://ec.europa.eu/environment/waste/weee/index_en.htm) Mark is on the label or Molded in the case
FCC PART 15 CLASS B
Japan: Voluntary Control Council for Interference (VCCI)
JAPAN TUV Rheinland-PSE GlobTek Inc to J60950-1(H26) , J55022(H22),J3000(H25).Please follow the procedure listed in the following link for proper import to Japan: https://www.globtek.com/r2/Szj4Vb
CCC to GB4943.1-2011; GB/T9254-2008 GB17625.1-2012, Tropical <2000
RoHS
Specifications of directive 2011/65/EU Annex VI (ROHS-2) with amendment 2015/863-EU (ROHS-3) http://www.ce-mark.com/Rohs%20final.pdf
No Logo
CB Certificate IEC 60950-1:2005 (2nd Edition), Am 1: 2009, CB report IEC 60950-1:2005 (2nd Edition), Am 1: 2009 and EN 60950-1:2006 + Am 1:2010 + Am 11:2009 + Am 12:2011
JAPAN TUV R-PSE, Cert. No. JD 50473430, to J62368-1(H30) , J55032(H29),J3000(H25)[15V or less]. Please reference the following website for guidelines on PSE regulations: https://www.globtek.com/r2/Szj4Vb
Conforms to UL Std. 1310 CLASS 2 Power Units Cert. to CSA Std. C22.2 NO. 223 Up to 36 volts
UL60950-1, cULus to UL 60950-1, 2nd Edition, 2007-03-27 and CSA C22.2 No. 60950-1-07, 2nd Edition, 2007-03
Efficiency: complies to section 301 of Energy Independence and Security Act (EISA) complies with Energy Star tier 2 (North America), ECP tier 2 (China), MEPS tier 2 (Australia), Code of Conduct (Europe)
SELV
safety/separated extra-low voltage IEC 60950-1: 2005 (2nd Edition) and/or EN 60950-1:2006
Class 2 Power Unit
cETLus-Cert 4007497 UL1310 Recognized Component up to 42.4 volts
IP52
Ingress Protection: ?IP52 to IEC60529:2001 Protected against dust - limited ingress (no harmful deposit) and Protected against direct sprays up to 15 degrees from the vertical
CE Mark: tested to comply with EN 55032.2012+AC.2013, Class B, EN610003-2, EN610003-3 including EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6N EN61000-4-11; EMI: Complies with EN55011 CLASS B and FCC Part 15B - On label or Molded in case
LPS
Limited Power Source 60950
No Logo Applicable
CB report 60950-1 2nd Ed
Certification # TC RU AR46.B.75423 Custom Union of Russia, Belarus and Kazakhstan